Pellet Mills in Egypt
Short answer: Quote a pellet mill on capacity at your hardest recipe and die size — not the catalogue maximum — plus motor kW, conditioner retention time, die and roller specification, and cooler and crumbler scope.
Catalogue capacity is quoted on an easy diet with a large die. A 3 mm broiler pellet at high fibre inclusion can run at half that. State the recipe, target die and moisture, and require the capacity figure to be tied to them, or the machine you commission will not produce the tonnage you costed.
Scope of supply to define
- Conditioner (single or double shaft) with steam control
- Pellet press, main motor and gearbox or belt drive
- Dies and rollers with the first spare set
- Counter-flow cooler and cooler discharge
- Crumbler and rotary or plansifter sieve
- Steam: boiler capacity, pressure reduction and traps
Specs to put in the RFQ
Every line below is a number or a named standard a supplier can be held to. Missing lines are where quotes stop being comparable.
| Specification | What to state | Why it matters |
|---|---|---|
| Rated capacity, qualified | t/h at a named recipe, die diameter and conditioning temperature | An unqualified t/h figure is unenforceable. Tie it to the diet you will actually run. |
| Die specification | Hole diameter (mm), effective thickness, compression ratio, steel grade | Compression ratio, not hole size alone, governs pellet durability index (PDI) and throughput. |
| Conditioner | Retention time in seconds, target 80–85 °C, single vs double shaft | Retention below about 30 seconds limits starch gelatinisation, and PDI falls with it. |
| Main motor | kW, voltage/frequency, starting method (soft start or VFD) | kW per tonne is the honest comparison between quotes; frequency mismatch is a common import failure. |
| Cooler | Counter-flow, discharge temperature ≤ ambient +5 °C, final moisture target | Under-cooled pellets mould in a hot-climate warehouse within weeks. |
| Acceptance | PDI target, fines percentage after sifter, capacity test duration | The three numbers that decide whether the line is accepted or not. |
Indicative cost bands
| Scale | Installed, USD | Basis |
|---|---|---|
| 2 t/h line | 70k–150k | Conditioner, press, cooler, crumbler, sifter — excluding steam. |
| 5 t/h line | 150k–330k | Double-shaft conditioner typical from this scale. |
| 10 t/h line | 300k–650k | Largest single line item in most mills. |
| 20 t/h line | 600k–1.3M | Usually two presses in parallel for recipe flexibility. |
Planning and procurement estimate only. Bands are compiled from FeedMatch quotation work, exclude duties, taxes and local civil works, and are not offers. Confirm every figure against supplier quotations for your site.
Sourcing this in Egypt
Turkish, Chinese and European (Dutch, Danish, Italian) manufacturers quote most Egyptian feed-machinery tenders; Turkish suppliers usually win on delivered cost and service proximity, European on process guarantees.
Alexandria and Damietta for containerised and break-bulk equipment, Ain Sokhna for Red Sea routings. Inland delivery to Delta and Upper Egypt sites is short, but silo sections and press frames are out-of-gauge and need permits.
400 V / 50 Hz, generally stable in industrial zones but voltage dips are common — specify soft starters or VFDs and confirm motor tolerance. Summer ambient above 40 °C requires cooler and control-panel derating.
Import settlement and FX availability drive timing as much as price. Confirm the payment instrument with your bank before the technical award, not after.
- Local fabrication of silos, structures and simple conveying is competitive; process machinery (press, mixer, dosing) is almost always imported.
- Ask every supplier for their Egyptian reference list with contactable plant contacts — installed base in the Delta is the fastest way to check service response.
- Specify Arabic-language operator training and Arabic HMI where the shift team is local.
Where these tenders go wrong
- Comparing prices between a quote that includes the cooler and one that does not.
- Forgetting boiler, water treatment and steam distribution, which pelleting cannot run without.
- Ordering a single spare die instead of the set that matches your recipe range.
- No PDI or fines acceptance figure, so pellet quality disputes have no reference.
Send this specification to suppliers serving Egypt
The request opens prefilled with the pellet mills spec lines above and Egypt as the delivery market. Add your capacity and timeline and we route it to suppliers that quote into this market. Sourcing is free for buyers; suppliers compensate FeedMatch.
FAQ
What should I specify when buying pellet mills in Egypt?
Quote a pellet mill on capacity at your hardest recipe and die size — not the catalogue maximum — plus motor kW, conditioner retention time, die and roller specification, and cooler and crumbler scope.
Which suppliers quote pellet mills into Egypt?
Turkish, Chinese and European (Dutch, Danish, Italian) manufacturers quote most Egyptian feed-machinery tenders; Turkish suppliers usually win on delivered cost and service proximity, European on process guarantees.
What does pellet mills cost?
Indicative installed bands run from 70k–150k USD for a 2 t/h line up to 600k–1.3M USD at 20 t/h line. These are planning ranges from quotation work, not offers, and exclude duties and local civil works.
What changes the specification in Egypt specifically?
400 V / 50 Hz, generally stable in industrial zones but voltage dips are common — specify soft starters or VFDs and confirm motor tolerance. Summer ambient above 40 °C requires cooler and control-panel derating. Alexandria and Damietta for containerised and break-bulk equipment, Ain Sokhna for Red Sea routings. Inland delivery to Delta and Upper Egypt sites is short, but silo sections and press frames are out-of-gauge and need permits.