Silos & Raw-Material Storage in Egypt
Short answer: Quote silos on live capacity in tonnes at the bulk density of your worst-flowing ingredient, plus roof and wind loading, aeration, level sensing and discharge type — capacity in m³ alone tells you nothing.
Silo tenders go wrong on units. Suppliers quote volume in m³; buyers plan in tonnes. Maize at 720 kg/m³ and soybean meal at 610 kg/m³ do not fill the same silo to the same tonnage, and pelleted feed is lower again. Specify per-ingredient tonnage and the silo set stops being a guess.
Scope of supply to define
- Galvanised or bolted steel silos, hopper or flat-bottom
- Ladders, cages, roof platform and safety cage
- Aeration fans, temperature cables, level sensors
- Discharge slide gates and sweep auger
- Foundation loading data and anchor bolt template
- Bagged storage racking and the covered intake bay
Specs to put in the RFQ
Every line below is a number or a named standard a supplier can be held to. Missing lines are where quotes stop being comparable.
| Specification | What to state | Why it matters |
|---|---|---|
| Live capacity | Tonnes per silo at a stated bulk density (kg/m³) per ingredient | The difference between m³ and tonnes at 610 vs 720 kg/m³ is roughly 18% of your storage plan. |
| Structure | Sheet thickness, galvanising grade (g/m² zinc), design wind speed and seismic zone | Under-galvanised sheet in a coastal or humid climate is a ten-year silo sold as a thirty-year one. |
| Bottom type | Hopper angle (typically 45–60°) or flat bottom with sweep auger | Meals and bran bridge on shallow hoppers. Angle is a flow decision, not a cost decision. |
| Aeration and monitoring | Fan m³/h per tonne, temperature cable count, level sensor type | Without temperature cables you find hot spots when the load is already spoiled. |
| Discharge | t/h discharge rate, gate type and actuation | Discharge below intake rate turns storage into the bottleneck of the whole mill. |
| Civil interface | Foundation loads, anchor bolt plan, who supplies the concrete | The most common scope gap between an equipment supplier and a local contractor. |
Indicative cost bands
| Scale | Installed, USD | Basis |
|---|---|---|
| Approx. 500 t total (2 t/h mill) | 40k–110k | Small bolted galvanised set with basic aeration. |
| Approx. 1,500 t total (5 t/h mill) | 90k–220k | Hopper silos plus temperature monitoring. |
| Approx. 3,000 t total (10 t/h mill) | 180k–420k | Includes intake bay and level sensing. |
| Approx. 6,000 t+ total (20 t/h mill) | 350k–800k | Flat-bottom bulk storage becomes cheaper per tonne at this scale. |
Planning and procurement estimate only. Bands are compiled from FeedMatch quotation work, exclude duties, taxes and local civil works, and are not offers. Confirm every figure against supplier quotations for your site.
Sourcing this in Egypt
Turkish, Chinese and European (Dutch, Danish, Italian) manufacturers quote most Egyptian feed-machinery tenders; Turkish suppliers usually win on delivered cost and service proximity, European on process guarantees.
Alexandria and Damietta for containerised and break-bulk equipment, Ain Sokhna for Red Sea routings. Inland delivery to Delta and Upper Egypt sites is short, but silo sections and press frames are out-of-gauge and need permits.
400 V / 50 Hz, generally stable in industrial zones but voltage dips are common — specify soft starters or VFDs and confirm motor tolerance. Summer ambient above 40 °C requires cooler and control-panel derating.
Import settlement and FX availability drive timing as much as price. Confirm the payment instrument with your bank before the technical award, not after.
- Local fabrication of silos, structures and simple conveying is competitive; process machinery (press, mixer, dosing) is almost always imported.
- Ask every supplier for their Egyptian reference list with contactable plant contacts — installed base in the Delta is the fastest way to check service response.
- Specify Arabic-language operator training and Arabic HMI where the shift team is local.
Where these tenders go wrong
- Ordering in m³ and discovering the tonnage shortfall after the foundation is poured.
- Excluding foundations from both the supplier and the contractor scope.
- No temperature monitoring on protein meals, which self-heat faster than grain.
- Sizing storage on average consumption instead of shipment size and lead time.
Send this specification to suppliers serving Egypt
The request opens prefilled with the silos & storage spec lines above and Egypt as the delivery market. Add your capacity and timeline and we route it to suppliers that quote into this market. Sourcing is free for buyers; suppliers compensate FeedMatch.
FAQ
What should I specify when buying silos & storage in Egypt?
Quote silos on live capacity in tonnes at the bulk density of your worst-flowing ingredient, plus roof and wind loading, aeration, level sensing and discharge type — capacity in m³ alone tells you nothing.
Which suppliers quote silos & storage into Egypt?
Turkish, Chinese and European (Dutch, Danish, Italian) manufacturers quote most Egyptian feed-machinery tenders; Turkish suppliers usually win on delivered cost and service proximity, European on process guarantees.
What does silos & storage cost?
Indicative installed bands run from 40k–110k USD for a approx. 500 t total (2 t/h mill) up to 350k–800k USD at approx. 6,000 t+ total (20 t/h mill). These are planning ranges from quotation work, not offers, and exclude duties and local civil works.
What changes the specification in Egypt specifically?
400 V / 50 Hz, generally stable in industrial zones but voltage dips are common — specify soft starters or VFDs and confirm motor tolerance. Summer ambient above 40 °C requires cooler and control-panel derating. Alexandria and Damietta for containerised and break-bulk equipment, Ain Sokhna for Red Sea routings. Inland delivery to Delta and Upper Egypt sites is short, but silo sections and press frames are out-of-gauge and need permits.